Skip to content

  • Home
  • What is CCNA?
  • New CCNA exam – 200-301

IPv6 address prefixes

January 26, 2016January 19, 2019 upravnik

Here is a summary of the most common address prefixes in IPv6:

ipv6 prefixes

Post navigation

IPv6 multicast addresses
IPv6 interface identifier
BGP performance
  • What is a network?
  • OSI & TCP/IP models
  • Local area network (LAN)
  • Wide area network
  • Encapsulation
  • Ethernet explained
  • Ethernet frame
  • MAC & IP addresses
  • Unicast, multicast, and broadcast addresses
  • Network devices
  • Network hubs explained
  • Network bridge explained
  • Network switch explained
  • Network router explained
  • Half duplex and full duplex
  • IEEE Ethernet standards
  • Cisco three-layer hierarchical model
  • Types of Ethernet cabling
  • Types of Ethernet cables – straight-through and crossover
  • Types of IP addresses
  • Classes of IP addresses
  • Private IP addresses explained
  • Subnetting explained
  • Subnet mask
  • Create subnets
  • CIDR (Classless inter-domain routing)
  • Ping explained
  • Traceroute explained
  • TCP/IP suite of protocols
  • TCP explained
  • UDP explained
  • Ports explained
  • ARP (Address Resolution Protocol) explained
  • DHCP & DNS
  • Telnet & SSH
  • FTP & TFTP
  • SNMP (Simple Network Management Protocol)
  • HTTP and HTTPS explained
  • NTP (Network Time Protocol)
  • APIPA (Automatic Private IP Addressing)
  • ICMP (Internet Control Message Protocol)
  • IP header
  • Cisco IOS overview
  • Power on a Cisco device
  • IOS command modes
  • Get help in IOS
  • Running & startup configuration
  • IOS basic commands
  • show command
  • Configure descriptions
  • Run privileged commands within global config mode
  • Ports on an IOS device
  • Pipe character in IOS
  • IOS boot sequence
  • Backing up IOS configuration
  • What is IP routing?
  • Connected, static & dynamic routes
  • Administrative distance & metric
  • Routing protocols
  • RIP overview
  • Configuring RIPv2
  • passive-interface command
  • RIP loop prevention
  • Advertise default routes using RIP
  • EIGRP overview
  • EIGRP configuration
  • Wildcard mask in EIGRP
  • EIGRP automatic & manual summarization
  • EIGRP authentication & load balancing
  • EIGRP Reliable Transport Protocol (RTP)
  • EIGRP Diffusing Update Algorithm (DUAL)
  • EIGRP summary
  • OSPF overview
  • OSPF configuration
  • Designated & Backup Designated Router
  • OSPF authentication
  • OSPF summarization
  • OSPF summary
  • Differences between OSPF and EIGRP
  • Comparing internal routing protocols (IGPs)
  • Layer 2 switching
  • How switches work
  • Collision & broadcast domain
  • CSMA/CD
  • What is a VLAN?
  • Access and trunk ports
  • Configuring VLANs
  • Configuring access & trunk ports
  • Frame tagging
  • IEEE 802.1Q
  • Inter-Switch Link (ISL)
  • Configuring voice VLANs
  • Configuring allowed VLANs
  • What is VTP?
  • VTP modes
  • VTP configuration
  • What is STP?
  • How STP works
  • Electing the Root Switch in STP
  • Selecting STP root port
  • Selecting STP designated port (DP)
  • What is RSTP?
  • How RSTP works
  • Configuring RSTP
  • What are ACLs?
  • Types of ACLs
  • Configuring standard ACLs
  • Configuring extended ACLs
  • Configuring named ACLs
  • What is NAT?
  • Static NAT
  • Dynamic NAT
  • Port Address Translation (PAT) configuration
  • What is IPv6?
  • IPv6 address format
  • Types of IPv6 addresses
  • IPv6 unicast addresses
  • IPv6 global unicast addresses
  • IPv6 unique local addresses
  • IPv6 link-local addresses
  • IPv6 multicast addresses
  • IPv6 address prefixes
  • IPv6 interface identifier
  • IPv6 transition options
  • IPv6 routing protocols
  • How to configure IPv6
  • RIPng
  • Differences between IPv4 and IPv6
  • Wildcard masks
  • Setting up Telnet
  • Setting up SSH
  • Port security
  • Types of memory on a Cisco device
  • Configure Cisco router as DHCP server
  • Configure NTP on a Cisco router
  • Cisco Discovery Protocol (CDP) overview
  • Map hostnames to IP addresses
  • Configure Cisco device as DNS client
  • Extended ping command
  • traceroute command
  • debug command
  • show processes command
  • Configure an IP address on a switch
  • Configure interVLAN routing
  • Configure ROAS
  • Configure static MAC address
  • Link Layer Discovery Protocol (LLDP)
  • IOS files
  • Configure speed and duplex
  • Interface range command
  • How to upgrade Cisco IOS
  • Copy files with FTP
  • show version command
  • TCP three-way handshake
  • Erasing configuration files
  • show interfaces status command
  • Configure Cisco router as a DHCP client
  • logging synchronous command
  • exec-timeout command
  • no ip domain-lookup command
  • Encrypt local usernames and passwords
  • Cisco console rollover cable
  • Create a static host route
  • Uniform Resource Locator (URL) structure
  • The ARP table on a Cisco router
  • Default static route
  • Configure timezone and Daylight Saving Time (DST)
  • DHCP relay agent
  • Interface status codes
  • Auxiliary Port on a Cisco router
  • Syslog explained
  • Syslog message format
  • About
  • Contact
  • Support our work
Copyright study-ccna.com 2020. All rights reserved. This is not an official Cisco website.
Proudly powered by WordPress | Education Hub by WEN Themes